Welcome Guest Search | Active Topics | Log In | Register

Official Honda CB750 Build Diary - Stages 73-80 Options
arpurchase
#1 Posted : 18 July 2015 11:38:37

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Pack 23 contains stages 73-76.

Stage 73 contains side stand,pivot,spring,footrests,rubber footrests and screws.

For this stage you will need the motor cycle, base frame, something to stand the model on and 6 AAA battery's.

Remove the ignition key from the bike frame and make sure the key on the base frame is switched of then remove the battery boxes covers from both frames and insert three battery's into each battery box, replace the covers and tighten the screws. Next place the frame on the base making sure the IR sensor and receiver are lined up with each other then insert the key into the frame and turn the key in the base to the red dot position.

Now we can test the electronics.

The Headlight, Instruments and Brake light

The right hand switch has a slider with a 'L' and 'H' above it, sliding it to the 'L' position should light up the headlight [dipped beam] ,instruments and brake light. Sliding the switch to the 'H' position will give a full beam effect. Next press the brake pedal and the brake light should glow brighter you can also turn the brake light on by turning the key in the base frame to the black dot position. Return the right slider to its off position.

The Indicators, Horn,Volume control,Starter switch and Kick starter.

The left slider has an 'L' and 'R' at either end sliding the switch to the left will turn on the left indicators and the right side when pushed to the right. The volume control when turned to the left will lower the sound and when turned to the right make it louder. The button below the left hand slider will make the horn work the right hand side button when pressed once will give the sound of the bike being started with the electric starter, pushing it again will be the sound of the bike ticking over. To stop the sound turn the key on the base frame to the off position. Pushing the kick starter down and letting go will also produce the sound of the engine starting again use the base frame key to switch off the sound.

If any of the above do not work firstly check all the connectors are seated correctly and if they still do not work contact customer services for replacement parts.

Take the fuel tank and remove the two Honda logos. Next support the main bike frame and remove the steering bolt,hold the front forks about 5mm forward of the frame and slide the fuel tank into position then replace the front forks onto the frame. Now use an 'A' type screw to fix the tank in position and replace the Honda logo, do the same for the other side.

Take the side stand and check the spring fits, I found that fitting the stand first then attaching the spring was the best way to do this. So fit the side stand to the frame using the threaded pin and allen key then mount the spring hook onto the stand and fix to the frame using a 'N' type screw. Check that the side stand pivots correctly.

Next take the two footrests and rubbers line each one up with the 'D' shaped hole and push gently home making a pair. Line up the left hand footrest with the frame making sure it lines up with the notch and press gently home. On the right side push down the brake pedal and move the oil hose to one side to fit the foot rest again pushing gently home

This concludes stage 73, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201053.JPG
P6201058.JPG
P6201059.JPG
P6201060.JPG
P6201062.JPG
P6201063.JPG
P6201064.JPG
P6201065.JPG
P6201066.JPG
P6201067.JPG
P6201069.JPG
P6201071.JPG
P6201073.JPG
P6201074.JPG
P6201075.JPG
P6201076.JPG
P6201077.JPG
P6201078.JPG
P6201080.JPG
P6201081.JPG
P6201082.JPG
P6201083.JPG
P6201085.JPG
P6201088.JPG
P6201089.JPG
P6201090.JPG
P6201092.JPG
P6201093.JPG
P6201094.JPG
P6201096.JPG
P6201098.JPG
P6201099.JPG
P6201100.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#2 Posted : 18 July 2015 11:47:34

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 74 contains Pillion left footrest,bracket,pivot,rubber,covers and screws.

Take the two screw hole covers noting that they are marked 'L' and 'R' fit the left cover to the headlight housing first making sure it align's with the notch and push gently home. Do the same for the right side.

Next take the pillion foot rest and rubber line it up with the 'D' shaped hole and push home. Now take the bracket and slide it onto the foot rest making sure the holes are aligned then place the pivot into the hole and using pliers wrapped in masking tape squeeze the pivot into place then check its movement. Line the footrest up with the left hand side silencer taking note of the notch at the top, Align the foot rest with the notch and fix in place with a 'P' type screw. Check that the footrest moves freely.

At this part of the instructions it is recommended that you use a silicon oil spray to dress the tryes and not the grease provided with the kit earlyer in the build.
This concludes stage 74, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201102.JPG
P6201103.JPG
P6201104.JPG
P6201105.JPG
P6201106.JPG
P6201107.JPG
P6201108.JPG
P6201109.JPG
P6201110.JPG
P6201111.JPG
P6201112.JPG
P6201114.JPG
P6201115.JPG
P6201116.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#3 Posted : 18 July 2015 11:58:30

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 75 contains Pillion right footrest,bracket,pivot,rubber and screws.

Follow the instructions in stage 74 to assemble and fit the right pillion foot rest.

his concludes stage 75, store any assembled parts safely in a bag labeled with the stage number for future use.
[/size]
arpurchase attached the following image(s):
P6201118.JPG
P6201119.JPG
P6201120.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#4 Posted : 18 July 2015 12:00:54

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 76 contains the seat base,hinges 'A', 'B' and screws.

Take hinge 'A' and line it up with the front end of the seat base then fix it in position with a 'G' type screw now do the same for hinge 'B' placing it at the rear of hinge 'A' and fixing in place with another 'G' type screw. Next take the seat base and line it up with the two mounting holes on the frame, use two 'T' type screws to fix it in place. Test that the seat moves correctly.


This concludes stage 76, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201123.JPG
P6201127.JPG
P6201128.JPG
P6201129.JPG
P6201134.JPG
P6201136.JPG
P6201138.JPG
P6201139.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#5 Posted : 18 July 2015 12:04:52

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Pack 24 contains stages 77-80

Stage 77 contains the seat and screws.

Line up the seat making sure the four pins are located into the four posts on the seat base once you are happy with the post locations push the seat gently home until the base hits the spacers. Check the movement of the seat and adjust if needed.

This concludes stage 77, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201141.JPG
P6201142.JPG
P6201145.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#6 Posted : 18 July 2015 12:06:45

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 78 contains the left rear view mirror.

For this stage you will need the Main assembly.

Remove the protective film from the mirror face then line up the stem with the 'D' shaped hole in the left handlebar grip. Hold the handlebar steady and gently push the mirror stem home.


This concludes stage 78, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201148.JPG
P6201151.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#7 Posted : 18 July 2015 12:08:17

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 79 contains the right rear view mirror.

For this stage you will need the Main assembly.

Fit the right hand mirror in the same way the left mirror was fitted.

This concludes stage 79, store any assembled parts safely in a bag labeled with the stage number for future use.
arpurchase attached the following image(s):
P6201152.JPG
P6201155.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

arpurchase
#8 Posted : 18 July 2015 12:10:07

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red MedalTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding build
Groups: Registered, Moderator, Official Builds, Global Forum Support, Administrators

Joined: 27/09/2011
Posts: 14,957
Points: 45,418
Location: Dudley
Stage 80 contains the Display base top plate, speaker frame and grille.

For this stage you will need the Main assembly and the display base.

Take the speaker frame and put it onto the speaker in the base making sure the lip faces uppermost then add the grill to the frame. Next remove the protective film from the base plate and fit it into the groove around the top of the display base making sure the hole for the speaker is positioned correctly. Next take the model and position it over the sensor you can use either the side or centre stand to do this.


This completes the construction of the Honda CB750 four, I hope you enjoy the build as much as I have!
arpurchase attached the following image(s):
P6201156.JPG
P6201158.JPG
P6201161.JPG
P6201162.JPG
P6201164.JPG
P6201166.JPG
P6201167.JPG
P6201170.JPG
P6201172.JPG
Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .

Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.184 seconds.
DeAgostini