Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 8 (UK) Options
Spal
#1 Posted : 13 December 2018 21:01:16

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,354
Points: 12,915
Location: West Yorkshire
Pack 8 contains parts for stages 28-31


Stage 28

Contents: Switch plate, Oil sump drain,Switch,Long gearshift bracket,Short gearshift bracket,Screw type R

Locate the circled hole in the side of the engine, and insert the long gearshift bracket into it.Place the short gearshift bracket onto the end of the long bracket, on the inside of the engine wall. The other end of the short bracket should rest on the switch. Once the two brackets are in position, insert screw R into the indicated hole in the long bracket andgently tighten the screw into place, ensuring that the parts stay in position as shown.Insert the switch into the switch plate.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL1526.JPG
IMGL1527.JPG
IMGL1528.JPG
IMGL1529.JPG
IMGL1530.JPG
IMGL1531.JPG
IMGL1535.JPG
Spal
#2 Posted : 15 December 2018 00:26:43

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,354
Points: 12,915
Location: West Yorkshire
Stage 29

Contents: Oil sump,Lenses x 2,Pinion,Screws J ,Screws F,Washers

Place the oil sump drain onto the oil sump, turning the oil sump over, hold the drain in position, and place the switch plate onto the posts and secure it there with a type J screw.Retrieve the engine and place the oil sump onto the bottom of it, aligning the hole in the tab with the hole in the engine.Secure the sump with a type J screw, then place one of the lenses into the hole in the side of the sump. Use a clear-drying glue to secure the lens if necessary.Secure the sump on the other side of the engine with another type J screw, and fit the second lens. Again use a clear drying glue if necessary.

Stage complete, carefully store any remaining parts in a stage labelled bag.


Spal attached the following image(s):
IMGL1536.JPG
IMGL1537.JPG
IMGL1539.JPG
IMGL1540.JPG
IMGL1541.JPG
IMGL1542.JPG
IMGL1543.JPG
IMGL1544.JPG
IMGL1545.JPG
IMGL1546.JPG
IMGL1547.JPG
Spal
#3 Posted : 16 December 2018 01:20:57

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,354
Points: 12,915
Location: West Yorkshire
Stage 30

Contents: Cover,Oil window,Bolt head,Plastic bolts x 2,Transparent lens

Place the lens and the bolt head into the indicated holes in the oil window using clear-drying glue to secure the parts if necessary.Insert the pins on the reverse of the oil window into the indicated holes in the side of the engine and press the window into place.Locating the slot on the rear of the cylinder block,press the cover into place, it will only fit in one way.Insert the two plastic bolts into the holes below the cover.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL1549.JPG
IMGL1550.JPG
IMGL1551.JPG
IMGL1552.JPG
IMGL1553.JPG
IMGL1554.JPG
IMGL1555.JPG
IMGL1556.JPG
IMGL1557.JPG
IMGL1558.JPG
IMGL1559.JPG
IMGL1560.JPG
Spal
#4 Posted : 16 December 2018 23:38:52

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,354
Points: 12,915
Location: West Yorkshire
Stage 31

Contents: Clutch case,Bolt head,Coupling plate,Tube,Screws B

Push one end of the tube onto the valve projecting from the plate.Now prepare the clutch case, the bolt head and the coupling plate. The bolt head fits into the larger hole, and the two smaller holes circled blue will take the coupling plate pins.Insert the bolt head into the hole,securing it with glue if necessary.Press the coupling plate into place on the clutch case.Place the clutch case onto the side of the engine, aligning the corresponding holes and using a type B screw to secure it to the engine.

Stage complete, carefully store any remaining parts in a stage labelled bag.


You can view the official video build for this pack here

https://www.youtube.com/...Xph5t4Y_J7U3u2oaId8WuxTv
Spal attached the following image(s):
IMGL1563.JPG
IMGL1564.JPG
IMGL1565.JPG
IMGL1566.JPG
IMGL1567.JPG
IMGL1568.JPG
IMGL1569.JPG
IMGL1570.JPG
IMGL1571.JPG
IMGL1572.JPG
IMGL1574.JPG
IMGL1575.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.111 seconds.
DeAgostini