Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 7 (USA) Options
Spal
#1 Posted : 29 August 2018 20:16:03

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,369
Points: 12,915
Location: West Yorkshire
Pack 7 contains parts for stages 24-27


Stage 24

Contents: Pipe,Couplings,Cover plate,Oil filter,Tube A

Remove the backing from the gasket, and place the gasket onto the head cover.Place the head cover onto the cylinder block, ensuring that you match the orientation of both parts as shown.Tighten two type B screws into the aligned holes of the block and the head cover, to fix the two parts together.Putting the cylinder block to one side, place one end of tube A onto the indicated pin of the pipe.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL0917.JPG
IMGL0919.JPG
IMGL0920.JPG
IMGL0921.JPG
IMGL0922.JPG
IMGL0923.JPG
IMGL0910.JPG
IMGL0911.JPG
IMGL0912.JPG
IMGL0913.JPG
IMGL0914.JPG
IMGL0915.JPG
IMGL0916.JPG
Spal
#2 Posted : 29 August 2018 20:18:34

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,369
Points: 12,915
Location: West Yorkshire
Stage 25

Contents: Engine block,Plate,Type B screws

Place the cylinder block onto the engine block,Tightening a type B screw into each of the holes inside the engine block.Position the plate onto the engine block, aligning the matching holes of both parts before securing with two type B screws.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL0924.JPG
IMGL0925.JPG
IMGL0926.JPG
IMGL0927.JPG
IMGL0928.JPG
IMGL0929.JPG
IMGL0930.JPG
IMGL0931.JPG
IMGL0932.JPG
IMGL0933.JPG
Spal
#3 Posted : 29 August 2018 20:20:51

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,369
Points: 12,915
Location: West Yorkshire
Stage 26

Contents: Crankcase,Switch,Switch plate,Type B screws

Fit the engine block and the crankcase together, tightening a type B screw into the side of the block.Turn the assembly around and tighten a second type B screw into the hole in the other side of the block.Take the cover plate, and
position it over the screw from Step 4. Use a little glue to secure it if necessary.Retrieve the oil filter and fit it into the circled hole in the engine, matching the raised part inside the filter with the notch in the engine. Press the
couplings into the holes adjacent to the oil filter.Retrieving the pipe and tube A from stage 24,fit the pipe into the couplings first before pressing the pins into the lugs on the cylinder block.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL0936.JPG
IMGL0937.JPG
IMGL0938.JPG
IMGL0939.JPG
IMGL0940.JPG
IMGL0941.JPG
IMGL0943.JPG
IMGL0944.JPG
IMGL0945.JPG
IMGL0946.JPG
IMGL0948.JPG
IMGL0949.JPG
Spal
#4 Posted : 29 August 2018 20:23:06

Rank: Super-Elite

Build-Diary Medal: Build-Diary Medal of HonourPublisher Medal: Article published MedalActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsRed Medal: Red Medal
Groups: Official Builds, Registered

Joined: 19/06/2013
Posts: 4,369
Points: 12,915
Location: West Yorkshire
Stage 27

Contents: Shaft end nut,Crankshaft cover,Crankcase detail,Cap

Locate the recess inside the engine block and having placed the switch plate into it secure it with a type B screw.Insert the switch into the plate and ensure it clicks into place.Turn the engine block so that you can locate the two holes where the shaft end nut will fit.Place the pins of the shaft end nut into the holes and press it home. Use a little glue if necessary to hold them in place.Now place the crankshaft cover over the end nut, aligning the pins of the cover with those in the engine. Use a little glue to secure if necessary.Take the crankcase detail and insert it into the circled holes, as shown.Insert the cap into the circled hole in the engine.

Stage complete, carefully store any remaining parts in a stage labelled bag.


You can view the official video build for this pack here

https://www.youtube.com/...CEsGom94e6WX&index=7
Spal attached the following image(s):
IMGL0951.JPG
IMGL0952.JPG
IMGL0953.JPG
IMGL0954.JPG
IMGL0957.JPG
IMGL0958.JPG
IMGL0960.JPG
IMGL0961.JPG
IMGL0962.JPG
IMGL0963.JPG
IMGL0964.JPG
IMGL0965.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.218 seconds.
DeAgostini